MG
MG sleeves for light cure 250 pcs
Very low stock (4 units)Regular price LE 140.00 EGPUnit price /Unavailable
Epic
Epic Light Cure sleeves 200pcs
Very low stock (1 unit)Regular price LE 175.00 EGPUnit price /Unavailable
How to Choose Light Cure Sleeves for Your Curing Light
- Optical Transmission (≥85% at 450–470 nm) — Light cure sleeves must transmit sufficient blue-light wavelength to activate the camphorquinone or alternative photoinitiator in composite and adhesive systems. Standard 20–25 µm clear PE film achieves ≥85% transmission at 450–470 nm. Thicker sleeves (>30 µm) reduce irradiance reaching the composite surface and must be compensated by extending the cure time proportionally.
- Tip Diameter Compatibility (5–12 mm Wand Tips) — Standard LED curing light tips range from 8–12 mm diameter for broad-aperture wands to 5–6 mm for narrow pediatric or access tips. The sleeve must accommodate the widest part of the wand body without splitting while maintaining a tight fit at the tip to prevent air gaps that scatter light at the cure surface.
- Irradiance Compensation (10–20% Output Reduction) — Even optically clear sleeves reduce effective irradiance at the composite surface by 10–20% due to reflection and scatter at the film interface. For minimum irradiance requirements (≥800 mW/cm² at the tip), compensate by extending cure time by the equivalent percentage: e.g. a 10% reduction requires extending a 20-second cure to 22 seconds to deliver equivalent energy dose.
- Pre-Formed vs Stretch-to-Fit Film — Pre-formed sleeves maintain uniform film thickness across the tip for consistent and predictable irradiance delivery; stretch-to-fit sleeves may thin unevenly at the tip after stretching, creating micro-hotspots or reduced-irradiance zones that result in incomplete polymerisation at the margins of the restoration.
- 250-Piece Pack Economics — A 250-piece MG pack at 140 EGP accommodates a practice placing 8 resin restorations per day over approximately 31 working days. Egyptian practices using curing lights for all bonding, adhesive, and composite procedures should calculate total daily exposures (including resin cement curing) to size orders correctly.
Light Cure Sleeves Available in Egypt
| Product | Pack Size | Optical Clarity | Price (EGP) |
|---|---|---|---|
| MG Sleeves for Light Cure | 250 pcs | Optically clear PE (≥85%) | 140 |
Availability & Delivery in Egypt
MedSTA supplies light cure sleeves from MG in 250-piece packs in EGP with same-day dispatch from Cairo. Cairo and Giza delivery within 1–3 business days; all other Egyptian governorates within 3–5 business days. Monthly supply arrangements are available for Egyptian restorative and cosmetic dental practices.
Frequently Asked Questions
Do light cure sleeves reduce curing light output and how do I compensate?
Do light cure sleeves reduce curing light output and how do I compensate?
Yes — optically clear PE light cure sleeves typically reduce irradiance at the composite surface by 10–20% due to reflection and light scatter at the film interface. To compensate: measure your curing light baseline output with a radiometer, then apply the sleeve and re-measure to determine the actual reduction percentage. Extend cure time by the same percentage — e.g. a 15% irradiance reduction requires extending a standard 20-second cure to 23 seconds to deliver an equivalent mW·s/cm² energy dose and achieve full photoinitiator conversion depth.
Can the same light cure sleeve be used for multiple curing applications in a single patient visit?
Can the same light cure sleeve be used for multiple curing applications in a single patient visit?
Yes — a single sleeve may be used throughout the entire restorative appointment for one patient, covering all composite increments, adhesive curing, and resin cement curing steps during that visit. Change to a fresh sleeve for the next patient. Do not attempt to disinfect or re-use a sleeve between patients — the thin PE film is single-use only and cannot withstand surface disinfectants without degrading optical clarity and barrier integrity.
What is the maximum curing tip diameter compatible with standard light cure sleeves?
What is the maximum curing tip diameter compatible with standard light cure sleeves?
Standard universal light cure sleeves in stretch-to-fit PE accommodate curing light tip diameters of 5–12 mm, covering the majority of LED curing wands used in Egyptian dental clinics including broad-aperture standard tips (8–12 mm) and narrow pediatric or deep-access tips (5–6 mm). For monowave or polywave LED units with wider aperture tips (>13 mm), confirm the sleeve internal diameter specification before ordering to ensure a snug fit without splitting at the widest point of the wand.
Are light cure sleeves optically compatible with both LED and plasma arc curing lights?
Are light cure sleeves optically compatible with both LED and plasma arc curing lights?
Yes — clear PE light cure sleeves are spectrally neutral and do not selectively filter the 390–470 nm wavelength range relevant to LED (blue-light) curing or the 380–520 nm range of plasma arc curing lights (PAC). Both light sources transmit through the sleeve at equivalent efficiency. The irradiance reduction of 10–20% applies equally across all curing light technologies; extend cure times proportionally regardless of which light source is used.
Does MedSTA supply light cure sleeves in 250-piece packs compatible with major LED curing units across Egypt?
Does MedSTA supply light cure sleeves in 250-piece packs compatible with major LED curing units across Egypt?
Yes — MedSTA supplies MG brand 250-piece light cure sleeves in EGP with same-day dispatch from Cairo. The universal stretch-to-fit design is compatible with LED curing lights from Woodpecker, COXO, 3M, Kerr, SDI, and other brands commonly used in Egyptian dental clinics. Cairo and Giza delivery within 1–3 business days; all other Egyptian governorates within 3–5 business days.